go to
> kadmin(8)
> kdestroy(1)
> passwd(1)
> syslog(3)
Homepage > Man Pages > Category > File Formats
Homepage > Man Pages > Name > P

pam_krb5

man page of pam_krb5

pam_krb5: Kerberos v5 PAM module

NAME

pam_krb5 - Kerberos v5 PAM module

SYNOPSIS

auth sufficient pam_krb5.so minimum_uid=1000 session required pam_krb5.so minimum_uid=1000 account required pam_krb5.so minimum_uid=1000 password sufficient pam_krb5.so minimum_uid=1000

DESCRIPTION

The Kerberos v5 service module for PAM, typically installed at /lib/security/pam_krb5.so, provides functionality for the four PAM operations: authentication, account management, session management, and password management. pam_krb5.so is a shared object that is dynamically loaded by the PAM subsystem as necessary, based on the system PAM configuration. PAM is a system for plugging in external authentication and session management modules so that each application doesn't have to know the best way to check user authentication or create a user session on that system. For details on how to configure PAM on your system, see the PAM man page, often pam(7). Here are the actions of this module when called from each group: auth Provides implementations of pam_authenticate() and pam_setcred(). The former takes the username from the PAM session, prompts for the user's password (unless configured to use an already-entered password), and then performs a Kerberos initial authentication, storing the obtained credentials (if successful) in a temporary ticket cache. The latter, depending on the flags it is called with, either takes the contents of the temporary ticket cache and writes it out to a persistant ticket cache owned by the user or uses the temporary ticket cache to refresh an existing user ticket cache. After doing the initial authentication, the Kerberos PAM module will attempt to obtain tickets for a key in the local system keytab and then verify those tickets. Unless this step is performed, the authentication is vulnerable to KDC spoofing, but it requires that the system have a local key and that the PAM module be running as a user that can read the keytab file (normally /etc/krb5.keytab. You can point the Kerberos PAM module at a different keytab with the keytab option. If that keytab cannot be read or if no keys are found in it, the default (potentially insecure) behavior is to skip this check. If you want to instead fail authentication if the obtained tickets cannot be checked, set "verify_ap_req_nofail" to true in the [libdefaults] section of /etc/krb5.conf. Note that this will affect applications other than this PAM module. By default, whenever the user is authenticated, a basic authorization check will also be done using krb5_kuserok(). The default behavior of this function is to check the user's account for a .k5login file and, if one is present, ensure that the user's principal is listed in that file. If .k5login is not present, the default check is to ensure that the user's principal is in the default local realm and the user portion of the principal matches the account name (this can be changed by configuring a custom aname to localname mapping in krb5.conf; see the Kerberos documentation for details). This can be customized with several configuration options; see below. If the username provided to PAM contains an "@" and Kerberos can, treating the username as a principal, map it to a local account name, pam_authenticate() will change the PAM user to that local account name. This allows users to log in with their Kerberos principal and let Kerberos do the mapping to an account. Be aware, however, that this facility cannot be used with OpenSSH. OpenSSH will reject usernames that don't match local accounts before this remapping can be done and will pass an invalid password to the PAM module. Also be aware that several other common PAM modules, such as pam_securetty, expect to be able to look up the user with getpwnam() and cannot be called before pam_krb5 if this feature is used. When pam_setcred() is called to initialize a new ticket cache, the environment variable KRB5CCNAME is set to the path to that ticket cache. By default, the cache will be named /tmp/krb5cc_UID_RANDOM where UID is the user's UID and RANDOM is six randomly-chosen letters. This can be configured with the ccache and ccache_dir options. If pam_setcred() initializes a new ticket cache, it will also set up that ticket cache so that it will be deleted when the PAM session is closed. Normally, the calling program (login, sshd, etc.) will run the user's shell as a sub-process, wait for it to exit, and then close the PAM session, thereby cleaning up the user's session. session Provides implementations of pam_open_session(), which is equivalent to calling pam_setcred() with the PAM_ESTABLISH_CRED flag, and pam_close_session(), which destroys the ticket cache created by pam_setcred(). account Provides an implementation of pam_acct_mgmt(). All it does is do the same authorization check as performed by the pam_authenticate() implementation described above. password Provides an implementation of pam_chauthtok(), which implements password changes. The user is prompted for their existing password (unless configured to use an already entered one) and the PAM module then obtains credentials for the special Kerberos principal "kadmin/changepw". It then prompts the user for a new password, twice to ensure that the user entered it properly (again, unless configured to use an already entered password), and then does a Kerberos password change. Unlike the normal Unix password module, this module will allow any user to change any other user's password if they know the old password. Also, unlike the normal Unix password module, root will always be prompted for the old password, since root has no special status in Kerberos. (To change passwords in Kerberos without knowing the old password, use kadmin(8) instead.) Both the account and session management calls of the Kerberos v5 PAM module will return PAM_IGNORE if called in the context of a PAM session for a user who did not authenticate with Kerberos (a return code of "ignore" in the Linux PAM configuration language). Note that this module assumes the network is available in order to do a Kerberos authentication, and if the network is not available, some Kerberos libraries have timeouts longer than the timeout imposed by the login process. This means that using this module incautiously can make it impossible to log on to console as root. For this reason, you should always use the ignore_root or minimum_uid options, list a local authentication module such as pam_unix first with a control field of "sufficient" so that the Kerberos PAM module will be skipped if local password authentication was successful. This is not the same PAM module as the Kerberos PAM module available from Sourceforge. It supports many of the same options, has some additional options, and doesn't support some of the options the Sourceforge module does.

CONFIGURATION

The Kerberos v5 PAM module takes many options, not all of which are relevant to every PAM group; options that are not relevant will be silently ignored. Any of these options can be set in the PAM configuration as arguments listed after "pam_krb5.so". Some of the options can also be set in the system krb5.conf file; if this is possible, it will be noted below in the option description. To set a boolean option in the PAM configuration file, just give the name of the option in the arguments. To set an option that takes an argument, follow the option name with an equal sign (=) and the value, with no separating whitespace. Whitespace in option arguments is not supported in the PAM configuration. To set an option for the PAM module in the system krb5.conf file, put that option in the [appdefaults] section. The Kerberos v5 PAM module will look for options either at the top level of the [appdefaults] section or in a subsection named "pam", inside or outside a section for the realm. For example, the following fragment of a krb5.conf file would set forwardable to true, minimum_uid to 1000, and set ignore_k5login only if the realm is EXAMPLE.COM. [appdefaults] forwardable = true pam = { minimum_uid = 1000 EXAMPLE.COM = { ignore_k5login = true } } For more information on the syntax of krb5.conf, see krb5.conf(5). Note that options that depend on the realm will be set only on the basis of the default realm, either as configured in krb5.conf(5) or as set by the realm option described below. If the user authenticates to an account qualified with a realm, that realm will not be used when determining which options will apply. There is no difference to the PAM module whether options are specified at the top level or in a "pam" section; the "pam" section is supported in case there are options that should be set for the PAM module but not for other applications. If the same option is set in krb5.conf and in the PAM configuration, the latter takes precedent. Note, however, that due to the configuration syntax, there's no way to turn off a boolean option in the PAM configuration that was turned on in krb5.conf. alt_auth_map=<format> This functions similarly to the search_k5login option. The <format> argument is used as the authentication Kerberos principal, with any %s in <format> replaced with the username. If the username contains an "@", only the part of the username before the realm is used to replace %s and the realm is appended to the result. There is no quote removal. If this option is present, the default behavior is to try this alternate principal first and then fall back to the standard behavior if it fails. The primary usage is to allow alternative principals to be used for authentication in programs like sudo. Most examples will look like: alt_auth_map=%s/root which attempts authentication as the root instance of the username first and then falls back to the regular username (but see force_alt_auth and only_alt_auth). This option can be set in krb5.conf, although normally it doesn't make sense to do that; normally it is used in the PAM options of configuration for specific programs. It is only applicable to the auth and account groups. If this option is set for the auth group, be sure to set it for the account group as well or account authorization may fail. banner=<banner> By default, the prompts when a user changes their password are: Current Kerberos password: Enter new Kerberos password: Retype new Kerberos password: The string "Kerberos" is inserted so that users aren't confused about which password they're changing. Setting this option replaces the word "Kerberos" with whatever this option is set to. Setting this option to the empty string removes the word before "password:" entirely. If set in the PAM configuration, <banner> may not contain whitespace. If you want a value containing whitespace, set it in krb5.conf. This option can be set in krb5.conf and is only applicable to the password group. ccache=<pattern> Use <pattern> as the pattern for creating credential cache names. <pattern> must be in the form <type>:<residual> where <type> and the following colon are optional if a file cache should be used. The special token %u, anywhere in <pattern>, is replaced with the user's numeric UID. The special token %p, anywhere in <pattern>, is replaced with the current process ID. If <pattern> ends in the literal string "XXXXXX" (six X's), that string will be replaced by randomly generated characters and the ticket cache will be created using mkstemp(3). This is strongly recommended if <pattern> points to a world-writable directory. This option can be set in krb5.conf and is only applicable to the auth and session groups. ccache_dir=<directory> Store user ticket caches in <directory> instead of in /tmp. The algorithm for generating the ticket cache name is otherwise unchanged. <directory> may be prefixed with "FILE:" to make the cache type unambiguous (and this may be required on systems that use a cache type other than file as the default). This option can be set in krb5.conf and is only applicable to the auth and session groups. clear_on_fail When changing passwords, PAM first does a preliminary check through the complete password stack, and then calls each module again to do the password change. After that preliminary check, the order of module invocation is fixed. This means that even if the Kerberos v5 password change fails (or if one of the other password changes in the stack fails), other password PAM modules in the stack will still be called even if the failing module is marked required or requisite. When using multiple password PAM modules to synchronize passwords between multiple systems when they change, this behavior can cause unwanted differences between the environments. Setting this option provides a way to work around this behavior. If this option is set and a Kerberos password change is attempted and fails (due to network errors or password strength checking on the KDC, for example), this module will clear the stored password in the PAM stack. This will force any subsequent modules that have use_authtok set to fail so that those environments won't get out of sync with the password in Kerberos. The Kerberos v5 PAM module will not meddle with the stored password if it skips the user due to configuration such as minimum_uid. Unfortunately, setting this option interferes with other desirable PAM configurations, such as attempting to change the password in Kerberos first and falling back on the local Unix password database if that fails. It therefore isn't the default. Turn it on (and list pam_krb5 first after pam_cracklib if used) when synchronizing passwords between multiple environments. This option can be set in krb5.conf and is only applicable to the password group. debug Log more verbose trace and debugging information to syslog at LOG_DEBUG priority, including entry and exit from each of the external PAM interfaces (except pam_close_session). This option can be set in krb5.conf. defer_pwchange By default, pam-krb5 lets the Kerberos library handle prompting for a password change if an account's password is expired during the auth group. If this fails, pam_authenticate() returns an error. According to the PAM standard, this is not the correct way to handle expired passwords. Instead, pam_authenticate() should return success without attempting a password change, and then pam_acct_mgmt() should return PAM_NEW_AUTHTOK_REQD, at which point the calling application is responsible for either rejecting the authentication or calling pam_chauthtok(). However, following the standard requires that all applications call pam_acct_mgmt() and check its return status; otherwise, expired accounts may be able to successfully authenticate. Many applications do not do this. If this option is set, pam-krb5 uses the fully correct PAM mechanism for handling expired accounts instead of failing in pam_authenticate(). Due to the security risk of widespread broken applications, be very careful about enabling this option. It should normally only be turned on to solve a specific problem (such as using Solaris Kerberos libraries that don't support prompting for password changes during authentication), and then only for specific applications known to call pam_acct_mgmt() and check its return status properly. This option can be set in krb5.conf and is only applicable to the auth group. expose_account By default, the Kerberos PAM module password prompt is simply "Password:". This avoids leaking any information about the system realm or account to principal conversions. If this option is set, the string "for <principal>" is added before the colon, where <principal> is the user's principal. This string is also added before the colon on prompts when changing the user's password. Enabling this option with ChallengeResponseAuthentication enabled in OpenSSH may cause problems for some ssh clients that only recognize "Password:" as a prompt. This option is automatically disabled if search_k5login is enabled since the principal displayed would be inaccurate. This option can be set in krb5.conf and is only applicable to the auth and password groups. fail_pwchange By default, pam-krb5 lets the Kerberos library handle prompting for a password change if an account's password is expired during the auth group. If this option is set, expired passwords are instead treated as an authentication failure identical to an incorrect password. Also see defer_pwchange and force_pwchange. This option can be set in krb5.conf and is only applicable to the auth group. force_alt_auth This option is used with alt_auth_map and forces authentication as the mapped principal if that principal exists in the KDC. Only if the KDC returns principal unknown does the Kerberos PAM module fall back to normal authentication. This can be used to force authentication with an alternate instance. If alt_auth_map is not set, it has no effect. This option can be set in krb5.conf and is only applicable to the auth group. force_first_pass Use the password obtained by a previous authentication or password module to authenticate the user without prompting the user again. If no previous module obtained the user's password, fail without prompting the user. Also see try_first_pass and use_first_pass for weaker versions of this option. This option is only applicable to the auth and password groups. For the password group, it applies only to the old password. See use_authtok for a similar setting for the new password. force_pwchange If this option is set and authentication fails with a Kerberos error indicating the user's password is expired, attempt to immediately change their password during the authenticate step. Under normal circumstances, this is unnecessary. Most Kerberos libraries will do this for you, and setting this option will prompt the user twice to change their password if the first attempt (done by the Kerberos library) fails. However, some system Kerberos libraries (such as Solaris's) have password change prompting disabled in the Kerberos library; on those systems, you can set this option to simulate the normal library behavior. This option can be set in krb5.conf and is only applicable to the auth group. forwardable Obtain forwardable tickets. If set (to either true or false, although it can only be set to false in krb5.conf), this overrides the Kerberos library default set in the [libdefaults] section of krb5.conf. This option can be set in krb5.conf and is only applicable to the auth group. ignore_k5login Never look for a .k5login file in the user's home directory. Instead, only check that the Kerberos principal maps to the local account name. The default check is to ensure the realm matches the local realm and the user portion of the principal matches the local account name, but this can be customized by setting up an aname to localname mapping in krb5.conf. This option can be set in krb5.conf and is only applicable to the auth and account groups. ignore_root Do not do anything if the username is "root". The authentication and password calls will silently fail (allowing that status to be ignored via a control of "optional" or "sufficient"), and the account and session calls (including pam_setcred) will return PAM_IGNORE, telling the PAM library to proceed as if they weren't mentioned in the PAM configuration. This option is supported and will remain, but normally you want to use minimum_uid instead. This option can be set in krb5.conf. keytab=<path> Specifies the keytab to use when validating the user's credentials. The default is the default system keytab (normally /etc/krb5.keytab), which is usually only readable by root. Applications not running as root that use this PAM module for authentication may wish to point it to another keytab the application can read. The first principal found in the keytab will be used as the principal for credential verification. This option can be set in krb5.conf and is only applicable to the auth group. minimum_uid=<uid> Do not do anything if the authenticated account name corresponds to a local account and that local account has a UID lower than <uid>. If both of those conditions are true, the authentication and password calls will silently fail (allowing that status to be ignored via a control of "optional" or "sufficient"), and the account and session calls (including pam_setcred) will return PAM_IGNORE, telling the PAM library to proceed as if they weren't mentioned in the PAM configuration. Using this option is highly recommended if you don't need to use Kerberos to authenticate password logins to the root account (which isn't recommended since Kerberos requires a network connection). It provides some defense in depth against user principals that happen to match a system account incorrectly authenticating as that system account. This option can be set in krb5.conf. no_ccache Do not create a ticket cache after authentication. This option shouldn't be set in general, but is useful as part of the PAM configuration for a particular service that uses PAM for authentication but isn't creating user sessions and doesn't want the overhead of ever writing the user credentials to disk. When using this option, the application should only call pam_authenticate(); other functions like pam_setcred(), pam_start_session(), and pam_acct_mgmt() don't make sense with this option. Don't use this option if the application needs PAM account and session management calls. This option is only applicable to the auth group. only_alt_auth This option is used with alt_auth_map and forces the use of the mapped principal for authentication. It disables fallback to normal authentication in all cases and overrides search_k5login and force_alt_auth. If alt_auth_map is not set, it has no effect and the standard authentication behavior is used. This option can be set in krb5.conf and is only applicable to the auth group. pkinit_anchors=<anchors> When doing PKINIT authentication, use <anchors> as the client trust anchors. This is normally a reference to a file containing the trusted certificate authorities. This option is only used if try_pkinit or use_pkinit are set. This option can be set in krb5.conf and is only applicable to the auth and password groups. pkinit_prompt Before attempting PKINIT authentication, prompt the user to insert a smart card. You may want to set this option for programs such as gnome-screensaver that call PAM as soon as the mouse is touched and don't give the user an opportunity to enter the smart card first. Any information entered at the first prompt is ignored. If try_pkinit is set, a user who wishes to use a password instead can just press Enter and then enter their password as normal. This option is only used if try_pkinit or use_pkinit are set. This option can be set in krb5.conf and is only applicable to the auth and password groups. pkinit_user=<userid> When doing PKINIT authentication, use <userid> as the user ID. The value of this string is highly dependent on the type of PKINIT implementation you're using, but will generally be something like: PKCS11:/usr/lib/pkcs11/lib/soft-pkcs11.so to specify the module to use with a smart card. It may also point to a user certificate or to other types of user IDs. See the Kerberos library documentation for more details. This option is only used if try_pkinit or use_pkinit are set. This option can be set in krb5.conf and is only applicable to the auth and password groups. preauth_opt=<option> Sets a preauth option (currently only applicable when built with MIT Kerberos). <option> is either a key/value pair with the key separated from the value by "=" or a boolean option (in which case it's turned on). In krb5.conf, multiple options should be separated by whitespace. In the PAM configuration, this option can be given multiple times to set multiple options. In either case, <option> may not contain whitespace. The primary use of this option, at least in the near future, will be to set options for the MIT Kerberos PKINIT support. For the full list of possible options, see the PKINIT plugin documentation. At the time of this writing, "X509_user_identity" is equivalent to pkinit_user and "X509_anchors" is equivalent to pkinit_anchors. "flag_DSA_PROTOCOL" can only be set via this option. Any settings made with this option are applied after the pkinit_anchors and pkinit_user options, so if an equivalent setting is made via preauth_opt, it will probably override the other setting. This option can be set in krb5.conf and is only applicable to the auth and password groups. Note that there is no way to remove a setting made in krb5.conf using the PAM configuration, but options set in the PAM configuration are applied after options set in krb5.conf and therefore may override earlier settings. prompt_principal Before prompting for the user's password (or using the previously entered password, if try_first_pass, use_first_pass, or force_first_pass are set), prompt the user for the Kerberos principal to use for authentication. This allows the user to authenticate with a different principal than the one corresponding to the local username, provided that either a .k5login file or local Kerberos principal to account mapping authorize that principal to access the local account. Be cautious when using this configuration option and don't use it with OpenSSH PasswordAuthentication, only ChallengeResponseAuthentication. Some PAM-enabled applications expect PAM modules to only prompt for passwords and may even blindly give the password to the first prompt, no matter what it is. Such applications, in combination with this option, may expose the user's password in log messages and Kerberos requests. realm=<realm> Obtain credentials in the specified realm rather than in the default realm for this system. If this option is used, it should be set for all groups being used for consistent results (although the account group currently doesn't care about realm). This will not change authorization decisions. If the obtained credentials are supposed to allow access to a shell account, the user will need an appropriate .k5login file entry or the system will have to have a custom aname_to_localname mapping. renew_lifetime=<lifetime> Obtain renewable tickets with a maximum renewable lifetime of <lifetime>. <lifetime> should be a Kerberos lifetime string such as "2d4h10m" or a time in minutes. If set, this overrides the Kerberos library default set in the [libdefaults] section of krb5.conf. This option can be set in krb5.conf and is only applicable to the auth group. retain_after_close Normally, the user's ticket cache is destroyed when either pam_end() or pam_close_session() is called by the authenticating application so that ticket caches aren't left behind after the user logs out. In some cases, however, this isn't desireable. (On Solaris 8, for instance, the default behavior means login will destroy the ticket cache before running the user's shell.) If this option is set, the PAM module will never destroy the user's ticket cache. If you set this, you may want to call kdestroy in the shell's logout configuration or run a temporary file removal program to avoid accumulating hundreds of ticket caches in /tmp. This option can be set in krb5.conf and is only applicable to the auth and session groups. search_k5login Normally, the Kerberos implementation of pam_authenticate attempts to obtain tickets for the authenticating username in the local realm. If this option is set and the local user has a .k5login file in their home directory, the module will instead open and read that .k5login file, attempting to use the supplied password to authenticate as each principal listed there in turn. If any of those authentications succeed, the user will be successfully authenticated; otherwise, authentication will fail. This option is useful for allowing password authentication (via console or sshd without GSS-API support) to shared accounts. If there is no .k5login file, the behavior is the same as normal. Using this option requires that the user's .k5login file be readable at the time of authentication. This option can be set in krb5.conf and is only applicable to the auth group. ticket_lifetime=<lifetime> Obtain tickets with a maximum lifetime of <lifetime>. <lifetime> should be a Kerberos lifetime string such as "2d4h10m" or a time in minutes. If set, this overrides the Kerberos library default set in the [libdefaults] section of krb5.conf. This option can be set in krb5.conf and is only applicable to the auth group. try_first_pass If the authentication module isn't the first on the stack, and a previous module obtained the user's password, use that password to authenticate the user without prompting them again. If that authentication fails, fall back on prompting the user for their password. This option has no effect if the authentication module is first in the stack or if no previous module obtained the user's password. Also see use_first_pass and force_first_pass for stronger versions of this option. This option is only applicable to the auth and password groups. For the password group, it applies only to the old password. try_pkinit Attempt PKINIT authentication before trying a regular password. You will probably also need to set the pkinit_user configuration option. If PKINIT fails, the PAM module will fall back on regular password authentication. This option is currently only supported if pam-krb5 was built against Heimdal 0.8rc1 or later or MIT Kerberos 1.6.3 or later. This option can be set in krb5.conf and is only applicable to the auth and password groups. use_authtok Use the new password obtained by a previous password module when changing passwords rather than prompting for the new password. If the new password isn't available, fail. This can be used to require passwords be checked by another, prior module, such as pam_cracklib. This option is only applicable to the password group. use_first_pass Use the password obtained by a previous authentication module to authenticate the user without prompting the user again. If no previous module obtained the user's password for either an authentication or password change, fall back on prompting the user. If a previous module did obtain the user's password but authentication with that password fails, fail without further prompting the user. Also see try_first_pass and force_first_pass for other versions of this option. This option is only applicable to the auth and password groups. For the password group, it applies only to the old password. See use_authtok for a similar setting for the new password. use_pkinit Require PKINIT authentication. You will probably also need to set the pkinit_user configuration option. If PKINIT fails, authentication will fail. This option is currently only supported if pam-krb5 was built against Heimdal 0.8rc1 or later. This option can be set in krb5.conf and is only applicable to the auth and password groups.
ENVIRONMENT
KRB5CCNAME Set by pam_setcred() with the PAM_ESTABLISH_CRED option, and therefore also by pam_open_session(), to point to the new credential cache for the user. See the ccache and ccache_dir options. By default, the cache name will be prefixed with "FILE:" to make the cache type unambiguous. PAM_KRB5CCNAME Set by pam_authenticate() to point to the temporary ticket cache used for authentication (unless the no_ccache option was given). pam_setcred() then uses that environment variable to locate the temporary cache even if it was not called in the same PAM session as pam_authenticate() (a problem with sshd running in some modes). This environment variable is only used internal to the PAM module.
FILES
/tmp/krb5cc_UID_RANDOM The default credential cache name. UID is the decimal UID of the local user and RANDOM is a random six-character string. The pattern may be changed with the ccache option and the directory with the ccache_dir option. /tmp/krb5cc_pam_RANDOM The credential cache name used for the temporary credential cache created by pam_authenticate(). This cache is removed again when the PAM session is ended or when pam_setcred() is called and will normally not be user-visible. RANDOM is a random six-character string. ~/.k5login File containing Kerberos principals that are allowed access to that account.

CAVEATS

Be sure to list this module in the session group as well as the auth group when using it for interactive logins. Otherwise, some applications (such as OpenSSH) will not set up the user's ticket cache correctly. The Kerberos library, via pam-krb5, will prompt the user to change their password if their password is expired, but when using OpenSSH, this will only work when ChallengeResponseAuthentication is enabled. Unless this option is enabled, OpenSSH doesn't pass PAM messages to the user and can only respond to a simple password prompt. If you are using MIT Kerberos, be aware that users whose passwords are expired will not be prompted to change their password unless the KDC configuration for your realm in [realms] in krb5.conf contains a master_kdc setting or, if using DNS SRV records, you have a DNS entry for _kerberos-master as well as _kerberos. pam_authenticate() returns failure when called for an ignored account, requiring the system administrator to use "optional" or "sufficient" to ignore the module and move on to the next module. It's arguably more correct to return PAM_IGNORE, which causes the module to be ignored as if it weren't in the configuration, but this increases the risk of inadvertent security holes when listing pam-krb5 as the only authentication module. This module treats the empty password as an authentication failure rather than attempting to use that password to avoid unwanted prompting behavior in the Kerberos libraries. If you have a Kerberos principal that intentionally has an empty password, it won't work with this module. This module will not refresh an existing ticket cache if called with an effective UID or GID different than the real UID or GID, since refreshing an existing ticket cache requires trusting the KRB5CCNAME environment variable and the environment should not be trusted in a setuid context. Old versions of OpenSSH are known to call pam_authenticate followed by pam_setcred(PAM_REINITIALIZE_CRED) without first calling pam_open_session, thereby requesting that an existing ticket cache be renewed (similar to what a screensaver would want) rather than requesting a new ticket cache be created. Since this behavior is indistinguishable at the PAM level from a screensaver, pam-krb5 when used with these old versions of OpenSSH will refresh the ticket cache of the OpenSSH daemon rather than setting up a new ticket cache for the user. The resulting ticket cache will have the correct permissions, but will not be named correctly or referenced in the user's environment and will be overwritten by the next user login. The best solution to this problem is to upgrade OpenSSH. I'm not sure exactly when this problem was fixed, but at the very least OpenSSH 4.3 and later do not exhibit it.

SEE ALSO

kadmin(8), kdestroy(1), krb5.conf(5), pam(7), passwd(1), syslog(3) The current version of this module is available from its web page at <//www.eyrie.org/~eagle/software/pam-krb5/>. PAM_KRB5(5)
 
 
 

Copyright © 2011–2018 by topics-of-interest.com . All rights reserved. Hosted by all-inkl.
Contact · Imprint · Privacy

Page generated in 122.65ms.

Ausf├╝hrliches AWeber Review | dfptutorial.com | schuhefinden.de